"Positioning Systems for Science and Industry Since 1967"
          (585) 657-6151

UniSlide Logo

MA25 Series UniSlide

Motor-Driven UniSlide® MA25 Series


The MA25 Series UniSlide stage has a body width of 2.5 inches, slider length of 2.5 inches carrying a 15 lbs. horizontal load. The MA25 can travel up to 20.5" with the 2.5" slider/carriage. The MA25 Series UniSlide is available in 7 lead screw pitches. Recommended step rate is 1000/steps per second.

MA25 Series UniSlides are comprised of an aluminum alloy extruded dovetail base with 60 degree opposing V-type ways. An aluminum alloy carriage that runs in the dovetail ways of the base. MA25 lead screws are constrained and supported with pre-loaded Delrin® thrust bearings, which have pre-loaded ball bearings. The lead screw drive nut is a tension adjustable nut made of Delrin providing low friction, and minimal backlash.

The MA25 Series is part of 5 motorized UniSlide Series. Others are MA15, MA40, MA60, MB90. There is also a manual version - the A25 Series.

 

 
UniSlide Specifications – Motor-Driven Assemblies

Factors such as size of the motor, size of the payload, travel distance, mounting direction/plane, etc. effect the actual capability of any assembly. Please contact Velmex Application Engineers to configure a system that will meet your exact requirements.

MA25 UniSlide UniSlide® MA25 Series#&8224;
Travel Distance‡ 0.5" - 24.5" 1.27 – 52.07 cm
Base Length 4" - 24" 10.16 – 60.96 cm
Slider Length 2.5" 6.35 cm
Weight 1.18 – 4.4 lbs. .82 – 2 kg.
Height** 0.81" 2.06 cm
Width 2.5" 6.35 cm
 
Maximum Horizontal Load 15 lbs. 6.8 kg.
Load Normal (LN)* 10 lbs. 4.54 kg.
Load Thrust (LT)* 7.5 lbs. 3.40 kg.
Cantilever Side (LCS)* 10 lb-in 1.13 N-m
Cantilever Inline (LCI)* 20 lb-in 2.26 N-m

† Motors sold separately.
* Normal Operating Loads are less than the maximum.
** Deeper "B" base configurations available.
‡ Standard travel distances available are in 3" increments.


Repeatability 0.00015" (4 microns) typical
Straight line accuracy Bow - 0.002" per foot; Run Out - 0.001" per foot; Twist - 1 milliradian per foot
Screw lead accuracy Standard Lead Screw: 0.007"/10" Precision Lead Screw: 0.0015"/10" or better available. Consult factory.
Operating temperature 0 to 180° F (-18 to 82° C)
Properties of Velmex Stages Information on stage composition, tolerances, wear and design for specialty applications.


Lead Screws Available for MA25 Series
MA25 Series Lead Screws

Basic Dimensions for MA25 Series UniSlide Assemblies

A15 Dimensions


UniSlide Configurations

The basic linear UniSlide is a 1-axis stage. UniSlides can be combined for multiple axes in a wide range of lengths and payload capacities. See Examples for images of various multi-axis UniSlides and combinations that include other Velmex stages.

UniSlide Configurations

 

Options/Accessories

An array of options and accessories is available for the MA25 Series UniSlide Assemblies

Adapter Plates

XY Plates – allow two UniSlides to be converted into an XY motion system. For more specifics and to see the adapter plates in use on a Velmex stage visit the UniSlide Adapters page.

A2500XY Adapter Plate

A2500XY Adapter Plate – To mount a MA25 Series UniSlide to another MA25 Series or to a MA15 Series in XY. (The MA25 would be the base stage.)

A4000XY Adapter Plate

A4000XY Adapter Plate – To mount a MA40 Series UniSlide to another AM40 Series or to a MA25 Series in XY. (The MA40 would be the base stage.)

XZ Plates – Allow UniSlide assemblies to be positioned vertically facing in any of four directions. For more specifics and to see the adapter plates in use on a Velmex stage visit the UniSlide Adapters page.

A2500XZ Adapter Plate

A2500XZ Adapter Plate – To mount a MA25 Series UniSlide to another MA25 Series (or to a MA15 in XZ. (The MA25 would be the base horizontal stage.)

A4000XZ Adapter Plate

A4000XZ Adapter Plate – To mount a MA40 Series UniSlide or a MA25 Series vertically to another MA40 Series in XZ. (The MA40 would be the base horizontal stage.)

XZ Brackets – allow UniSlide assemblies to be positioned vertically, facing in any of four directions and perpendicular to the X or Y plane. For more specifics and to see the brackets in use on a Velmex stage visit the UniSlide Adapters page.

XZ Adapter Brackets - A25 Series

A2501XZ Adapter Bracket – To mount a MA25 Series UniSlide to another MA25 Series (6"- 9") or to an A15 Series (6"- 9") in XZ. (The MA25 would be the base horizontal stage. The other stage would be mounted vertically.)
B2503XZ Adapter Bracket –To mount a MA25 Series UniSlide to another MA25 Series (over 9") or to a MA15 Series (over 9") in XZ. (The MA25 would be the base horizontal stage.)

XZ Adapter Brackets - A40 Series

A4001XZ Adapter Bracket – To mount a MA40 Series UniSlide (6"- 9") or a MA25 Series (6"- 9") vertically to another MA40 Series in XZ. (The MA40 would be the upper horizontal stage.) Can also mount two B4800TS Rotary Tables at right angles.
B4003XZ Adapter Bracket –To mount a MA40 Series UniSlide to another MA40 Series (12"- 15") or to a MA25 Series (12"- 15") in XZ. (The MA40 would be the base horizontal stage.)
B4004XZ Adapter Bracket – To mount a MA40 Series UniSlide to another MA40 Series (over 15") or to a MA25 Series (over 15") in XZ. (The MA40 would be the base horizontal stage.)

B5990TXZ Rotary Adapter Plates

Rotary Table Adapter Plates –To mount Velmex Rotary Tables to UniSlide Assemblies either in horizontal or vertical positions.

 

B5990TXZ-BK Adapter Plate – To mount two B5990TS Rotary Tables at right angles to each other or to mount a B5990TS to any MA Series UniSlide.

Platform Shelves

Platform Shelf – A right angled bracket designed to be used with UniSlide® Elevating Tables. However, they also can be used with vertically mounted UniSlide Assemblies to support a payload. The shelf can be inverted depending on the motion required.

For more specifics and to see the shelf in use on a Velmex stage visit the UniSlide Adapters page.

UniSlides with two different size sliders

Slider Lengths – Varying length carriages (sliders) can be added to all models of UniSlide Assemblies. Choosing a longer slider reduces the standard travel distance. 2.5" is the standard slider on the MA25 Series. Optional lengths available for the MA25 are 3" or 4".

Left Right Screw Motion

Left-Right Screw Motion (-LR) – This configuration is very useful for applications where two objects must share a common axis of movement. This assembly incorporates two carriages driven by a single right- and left-hand threaded lead screw. When the knob is turned, the carriages simultaneously move toward or away from each other.

Independent Left-Right Slider UniSlide

Two Independent Carriages (-DS) – a variation on the left-right screw motion UniSlide is one containing two lead screws with control knobs at both ends of the assembly. Each lead screw and carriage operates independently.

Fixed Limit Switches on UniSlide

Limit Switches – Outboard adjustable and fixed end-of-travel limit switches are available as an option.

 

Outboard Adjustable Limit Switches – Mounted on the side rib of Velmex UniSlide Assemblies, these switches can be used to stop travel, provide more stops than the standard two, over-travel a stop point, change speed or be active in only one direction.

Fixed, End-of-travel Limit Switches – These push button switches are fixed on the outside rib of Velmex Unislide Assemblies. They are not adjustable. (Pictured MA15 and MA25 versions.)

See Limits for more information.

Way covers on motorized UniSlides

Way Covers (-WC) – Protect the slider and dovetail base from dust, dirt and grit that could hamper the efficient operation of the slide. Way covers increase slider height and reduce the travel length of linear UniSlide stages. Not available on Motorized Series MA15 Assemblies.

Black Anodized UniSlide

Finishes – Standard UniSlide Assemblies have a brushed aluminum finish. Optional finishes are available at an additional charge and include:

 

• Black Anodizing, additional colors also available. (pictured)
• Hard Coat Anodized and dyed black
• Electroless Nickel Plated
• Specialized coatings for specific applications such as food processing or medical applications
• Modifications for use in a vacuum environment

VRO with an UniSlide Assembly

Encoders and VRO™ Encoder Readout For a high resolution position readout an encoder and Velmex's VRO encoder readout can be mounted to most linear UniSlide assemblies. An encoder, mounted directly to the slider gives a true and accurate reading eliminating lead screw and backlash errors. (Not available on all UniSlide models.) SEE: Velmex Controls on the Encoders and the VRO Readout for additional details.

Double Shaft Motor with Control Knob

Motorized / Manual OperationIt is possible, using a double shaft motor, to produce a Velmex stage that can be manually operated or motor-driven. A shaft extension accommodates the either a Rogan or standard aluminum knob.

The motor is purchased separately. Customers can mount their own motors, if they chose.

Stepper Motor

Motors A variety of motors are available to power Velmex UniSlides, most popular of which is the DC step motor. Gear motors, servo motors and high resolution step motors in both AC and DC can run Velmex UniSlides. SEE: Velmex Controls on the Motors for additional details.

The motor is purchased separately. Customers can mount their own motors, if they chose.

UniSlide with a VXM Controller

VXM™ Controller Step motors coupled with a motor controller like the Velmex VXM are a cost effective solution for accurate speed and precise incremental positioning. SEE: Velmex Controls on the VXM Controller for additional details.

Velmex offers a multitude of options and accessories for all its products. Usually an option or an accessory will address your requirements. When it doesn't, we can make custom modifications, including:

• Additional holes or slots. (A drawing is required.)

• Intermediate plates to mount your payload

• Special or in between lengths of the dovetail base

• Lead screw shaft extensions

• Choice of drive nut materials, including brass and Vespel

 


For .STP files, you may need to right click on the download button and save the "target" or "link".


Series Type File Name Description Download View
0.5" Travel
MA25 STP MA2504.stp Series MA25, 0.5" travel Download Button -
MA25 SAT MA2504.sat Series MA25, 0.5" travel Download Button -
2.5" Travel
MA25 STP MA2506.stp Series MA25, 2.5" travel Download Button -
MA25 SAT MA2506.sat Series MA25, 2.5" travel Download Button -
5.5" Travel
MA25 STP MA2509.stp Series MA25, 5.5" travel Download Button -
MA25 SAT MA2509.sat Series MA25, 5.5" travel Download Button -
MA25 STP MA2509xxx-S2.5-LR.stp Series MA25, 5.5" travel, left / right lead screw Download Button -
8.5" Travel
MA25 STP MA2512.stp Series MA25, 8.5" travel Download Button -
MA25 SAT MA2512.sat Series MA25, 8.5" travel Download Button -
MA25 STP MA2512xx-S2.5 NEMA 23.stp Series MA25, 8.5" travel, NEMA 23 Stepper Motor Download Button -
MA25 STP MA2512xxx-S2.5.stp Series MA25, 8.5" travel Download Button -
11.5" Travel
MA25 STP MA2515.stp Series MA25, 11.5" travel Download Button -
MA25 SAT MA2515.sat Series MA25, 11.5" travel Download Button -
14.5" Travel
MA25 STP MA2518.stp Series MA25, 14.5" travel Download Button -
MA25 SAT MA2518.sat Series MA25, 14.5" travel Download Button -
17.5" Travel
MA25 STP MA2521.stp Series MA25, 17.5" travel Download Button -
MA25 SAT MA2521.sat Series MA25, 17.5" travel Download Button -
MA25 STP MA2521xx-S2.5 NEMA 23.stp Series MA25, 17.5" travel, Nema 23 Stepper Motor Download Button -
MA25 STP MA2521xxx-S2.5.stp Series MA25, 17.5" travel Download Button -
20.5" Travel
MA25 STP MA2524.stp Series MA25, 20.5" travel Download Button -
MA25 SAT MA2524.sat Series MA25, 20.5" travel Download Button -
23.5" Travel
MA25 STP MA2527.stp Series MA25, 23.5" travel Download Button -
MA25 SAT MA2527.sat Series MA25, 23.5" travel Download Button -